|
|
快点注册登录,一起玩更精彩!
您需要 登录 才可以下载或查看，没有帐号？加入我们
x
Hello everybody! These are file. & I, z2 ]: z7 ?5 Y
Everyone know what's Menowa *? That is Mr. Umakote! !
! K6 e/ l q# U$ S& I( r5 y- h- \This genre is the first time Penn remodeling, we published the first how to make a mod N takes a second for his work permit. * This is not the image I want to p soon with pictures Daewoo Making
4 g J8 K0 e) _9 v U● Supachi × 1 (if you long × 2)
$ w8 A, z6 C7 |3 o% t. N" D2 ~' S2 S● 2 system cap KT + w$ m9 \+ ]6 T( q
● × two chestnuts poison Eaburan × 2 . N" k. h$ D4 y2 D
● Hyper-Gel × 1, O0 N% H7 S9 v& z$ y
● Enibo qs long if you/ @$ Y1 l3 n- A T' m5 O* @5 ~) L* F# }
● round stic Grip × 1 $ |! m4 }/ J- u6 l3 ]
●2 silver ring on the grip with the air I fit you like
, M9 r# P8 z, @( ^5 Q+ m5 C● the rubber cap in the G3 (?) × 2
s- w! s/ z$ ?● plastic tape, Scotch tape, etc. Here is how to make <1> ... , F6 g7 S P1 ^7 R5 w, H
I write in pen and ink Supachi first (?) Disconnect (pen hip intact. If you also take a long ass pen). ! ]7 F; C0 Z+ E. _: U$ o" u7 b
<2> ... then the KT cap tube.
' |6 y/ R/ n" ~) k; Z) H/ t, V3 a<3> to bind the chip ... the chip Eaburan poison chestnut (chestnut is like poison in the air covering the chip-chip brands.) We recommend that you stick with glue.
0 Z; M8 a5 a+ _7 Z& o, P6 e3 H0 c<4> ... will have four to five millimeters was cut into the grip Gel hapa. K# R' u; |. Q% L& [4 S2 F% P
<5> it ... <4> give you a double portion of the poisoning of the air out of the chip Blanc chestnut chips.
0 n+ r0 |1 Q0 f* y<6> ... silver rings on both ends of the air fit to your liking (at Hapa Gel Grip) to give.
% r d" e0 w) G, x; f* C% l<7 >...< 3> to <6> and the chip was in contrast to the usual <2> into the cap. >> Supachi <<looks like this ←. . But, when this state union body, the nib of Supachi, I think it is a gap of about 1 millimeter lye between the chip cap with KT, the appropriate grip (Hapajeru) to fill it with the ( I think both sides一応center of gravity shifts. If you are long, so I think Akanai gap, this work is not necessary). z w. `* z9 b, A( y3 S
<8 >...< 7> in the scotch tape to secure. }# r7 H& p6 I! \! O
<9 >...< 8> Supachi union on both sides of the
5 n0 |5 y. k/ a# A$ |. |<10> ... give Enibo appropriately across # ~4 w! j5 s2 e
<11> ... the rubber cap into the G3 in your choice (?) the air Put in a blank chip and decorated with Binite. Completed! ※ If you want long, cut to two at a dose of Supachi vicgotgame mod, cut into round stic Grip combines with an appropriate length (Supachi is cut to a length of about 6.2mm with 2 Then I would just about 20cm). ~ W and I hope to make many more, [! F) A. X: F3 F/ X
(supachip->supertip )
3 G+ `1 X- Y8 y& o(Enibo-> anyball) |
|
发表于 2012-8-25 17:14:43
发表于 2012-8-25 17:21:14
楼主
