|
|
快点注册登录,一起玩更精彩!
您需要 登录 才可以下载或查看，没有帐号？加入我们
x
G1-TwinNP
4 h5 X$ C) A- @2 f. ^! H) e0 GMod by cyshing0 o; \. u9 t$ J6 F' X# {
3 j% R0 ^' w& Y
Stats2 G) }5 \: ?" X" L) F
Length: 17.9 cm
3 I) y4 l, R2 F3 _9 vThickness: 1 cm9 v$ A( m9 s& o8 ^9 n/ W8 A1 s3 M
Weight: Moderate~Heavy& n7 s4 F) V0 B9 k% E
Balance: COP is in the middle of pen5 W! g9 |0 f/ o! M% H: H
Type: double-sided, non-retractable, writable
' r \1 O$ `* I4 j$ p9 C. Z8 l
$ I0 o* |: \7 c( x0 U5 s- pMaterials ?* V5 q4 P5 X) Y1 O
2 x G1 tips2 g8 f5 q0 U: i! q9 C; T9 l
1 x MonAmi Twin Name Pen4 y7 Y" n' B! t% Z: r. b; _: h
1 x (Dong-A/BUNCHO/Profile) Anyball grip1 P* F( h2 a }& k5 L- I
) b; i- O8 P7 P
6 t* d' Q4 N. D) g u
' _1 d! `8 ~4 z hConstruction# ]: t g' y% F$ d8 s
Step 1+ m; F, R3 O" L3 H9 q
Cut the Anyball grip into 2 pieces using cutter.
! c; [1 }# A6 @, N1 NUse nail clipper to cut the Twin Name Pen's clip then just sand the cut part a bit if it is not smooth after the cut. 4 S) D4 I/ B( T5 Z
Take off the metal tips from Pilot G1.
) \& V4 O. z' w! E# `# t; Z7 c. h* B0 A S( `
I' L, {$ `# R/ Z0 M- DStep 2
* A: p* W8 o$ W" \1 `) H% a0 Q; M' r1 IUse adhesive tape(aka wire tape) to tape the G1 tips on both end side of the caps. Wrap the tape a few rounds so that it's as thick as the cap(see pic).1 a: f1 ]( ?9 P9 A @
$ x( O# ?! k& Z& b+ b: r, \1 a4 p; p% V: F1 n1 ~, d: b
) p9 Z3 a: ]; n9 e& U7 n
$ k# F4 g- ]( S/ ZStep 3
4 }- j3 a% w# f4 a3 VPut the 2 pieces of grips on both ends. Done.
/ j0 j h# p* N: y @# [ . _8 I. S, l) @. q) P$ g2 L W: m3 N1 D1 O
登录/注册后可看大图
. R; H, E, k( A5 [6 X2 A9 C( }: l* c. }
若不可贴英文版，就请告诉我，大约农历新年时会翻译成华文。那时可能会贴个改良版的，因为刚听了DaThroat和ellusion67的建议。如果可以贴英文版，那我就懒惰翻译咯。:P
: U% L2 n) |* ^" X' r
- V: T0 ? m2 a[ 本帖最后由 cyshing 于 2008-1-6 00:24 编辑 ] |
|
[鸡蛋100个] 
acchanわ かわいね~ˋ( ° ▽、° )
发表于 2008-1-6 00:17:45
- W9 m2 _5 f& z$ a% }* |) \
6 s! b9 c% e$ L% o' a* E2 n
( e, l0 H3 m, h
发表于 2008-1-6 00:19:49
楼主
