|
|
快点注册登录,一起玩更精彩!
您需要 登录 才可以下载或查看，没有帐号？加入我们
x
G1-TwinNP
+ \- ~" b) V+ |/ J1 d$ ?7 H8 k+ R m7 VMod by cyshing& J! D! ]# ^- Z+ u' p
3 j) @( {0 w8 i6 QStats
( `: J" H* z" `0 cLength: 17.9 cm
. a4 |" k. P. I7 x% Q5 u) J0 y1 UThickness: 1 cm: o0 e+ S+ X" S( F% q
Weight: Moderate~Heavy
+ U0 Z; W' K: K6 c) \+ g; g' VBalance: COP is in the middle of pen2 W' E- f9 T4 S" y9 s3 x6 b7 o
Type: double-sided, non-retractable, writable
( v: t' V$ r F* e" `* B2 Z
8 [8 D( [ ]. z# f" X' J* EMaterials- y. w& G1 G2 X2 `/ J% O. W
2 x G1 tips
6 ~0 f i9 X. Y$ @2 | 1 x MonAmi Twin Name Pen7 u) J8 [+ [8 O
1 x (Dong-A/BUNCHO/Profile) Anyball grip5 Z9 ^: [! ?9 n2 a( m) T3 B$ V: q( j
) a7 l+ j( _9 v" _; [# {& l4 }. L# u5 |7 m; I, X( {; x
! f9 ~9 T; e( c/ i. mConstruction
# p& e* n0 p$ S+ S9 o2 }3 l$ h: e2 Q3 ]# aStep 1
& h+ A4 T' N+ ~+ P& ^7 {Cut the Anyball grip into 2 pieces using cutter.! J, G1 s$ V# F! L9 h
Use nail clipper to cut the Twin Name Pen's clip then just sand the cut part a bit if it is not smooth after the cut. 0 f# z0 x$ b/ a7 }$ u* C l
Take off the metal tips from Pilot G1.
9 i) G& Q& w6 b5 K
2 R2 i7 |; h# b h- r# [
2 Q6 v z8 Z/ M T4 B9 jStep 2
& W/ ^) b* } l' F9 x7 OUse adhesive tape(aka wire tape) to tape the G1 tips on both end side of the caps. Wrap the tape a few rounds so that it's as thick as the cap(see pic).
9 H q8 F& X3 B) o4 t; ^5 o& |0 P# {$ p2 r8 h
" Q+ i( \) _" } Z
) z# Z- ~5 S+ @- r) Q
: N+ u9 [5 l/ H; X
Step 39 ^: S! `. i% }* |
Put the 2 pieces of grips on both ends. Done.# N2 p/ L& R6 L, I) a$ C5 q
3 K! H+ W% w9 P/ }$ H2 F
3 \; D9 _7 t: R }# w& {( L0 Z若不可贴英文版，就请告诉我，大约农历新年时会翻译成华文。那时可能会贴个改良版的，因为刚听了DaThroat和ellusion67的建议。如果可以贴英文版，那我就懒惰翻译咯。:P
8 y4 `: ]4 I+ B! G* O$ ^7 L: o y+ R. q7 ]$ L* s( J6 `0 [
[ 本帖最后由 cyshing 于 2008-1-6 00:24 编辑 ] |
|
[鸡蛋100个] 
acchanわ かわいね~ˋ( ° ▽、° )
发表于 2008-1-6 00:17:45
' N# i2 ~% X6 y7 f
9 L9 ?" _# v9 f% a& r- l; ^6 |1 r
1 ?) _1 s: l$ T6 W9 I# F
发表于 2008-1-6 00:19:49
楼主
