|
|
快点注册登录,一起玩更精彩!
您需要 登录 才可以下载或查看，没有帐号？加入我们
x
G1-TwinNP
0 v( j9 W$ ], ]4 D& {' e# E$ Z$ d& ^# UMod by cyshing( a" M! J5 b7 X/ Q$ `/ N- Z
( _" w- A5 |( w& P# R4 Z$ S' h) s
Stats
) C) U, R! b% \: E" i9 `) |( PLength: 17.9 cm
+ L1 [) ^) G# ZThickness: 1 cm
6 \* A& y w$ c# ?9 J# jWeight: Moderate~Heavy
/ l. X, S- J: P5 B& E$ ZBalance: COP is in the middle of pen
, L& ^5 k a' C/ qType: double-sided, non-retractable, writable
6 `9 B; P; @+ t
W6 J" v( M S" pMaterials$ L7 U& C8 ~4 @8 M+ v
2 x G1 tips
* P: a% [* n4 `5 O, ? 1 x MonAmi Twin Name Pen& A2 M! ^8 n) h, L" M" c( v
1 x (Dong-A/BUNCHO/Profile) Anyball grip) [: x6 i3 d# |* H! B2 \ B2 p4 j& \
+ h# b, z) Q) j4 w6 H
) I, V- C( O$ V
8 h- c% o1 ?; p) R" Z$ ~6 _
Construction
0 y) K& @6 @$ MStep 1" R0 e8 Y8 [4 B* s# o
Cut the Anyball grip into 2 pieces using cutter.
8 @% j" \' L3 jUse nail clipper to cut the Twin Name Pen's clip then just sand the cut part a bit if it is not smooth after the cut.
8 l* y, s& k) ~; V, Y U9 LTake off the metal tips from Pilot G1./ U# Y9 q9 O/ |
% @8 }- m4 }; c, F# t5 h- C4 U* d. [4 H
Step 26 c$ n% p0 m( Q* B2 o/ G* H* B
Use adhesive tape(aka wire tape) to tape the G1 tips on both end side of the caps. Wrap the tape a few rounds so that it's as thick as the cap(see pic).
% w( m( Y- |5 Y
1 q& S k" c+ c+ i9 p5 M$ D: v
; |( I* L& e4 y% n9 X
) v# l% G8 M1 N" v& B
( v+ ^& T3 q6 _8 U0 E5 FStep 3- l& G$ [5 }4 \2 r, x8 ?
Put the 2 pieces of grips on both ends. Done.
' ]! n2 M1 j) v; U8 t$ d7 s! b6 { C' P' v9 |
1 U' _- i- {; A6 @若不可贴英文版，就请告诉我，大约农历新年时会翻译成华文。那时可能会贴个改良版的，因为刚听了DaThroat和ellusion67的建议。如果可以贴英文版，那我就懒惰翻译咯。:P- w5 `) N. L u% L
) D* p5 l8 x( t1 u
[ 本帖最后由 cyshing 于 2008-1-6 00:24 编辑 ] |
|
[鸡蛋100个] 
acchanわ かわいね~ˋ( ° ▽、° )
发表于 2008-1-6 00:17:45
' K' q/ {, V/ U8 ?2 W* J
2 W Z2 ~& D, q& I8 X$ W
4 Q7 x6 B u' f; N' o8 V
发表于 2008-1-6 00:19:49
楼主
